# Extension Cord Length and Amperage Chart: How Long a Cord Can Run for Your Load

Read a cord length and amperage chart the plain way: match wire gauge, amps and watts, work out voltage drop, and keep every run within a safe continuous load.

An extension cord carries less current as it gets longer, because resistance in the wire turns some voltage into heat. The chart that matters pairs a wire gauge (AWG, the wire thickness standard) with amps for a given run length. A cord that is too thin or too long for its load overheats, so you match gauge, length and current together. 

- Longer runs need thicker wire for the same current.
- Amperage rating falls as the run gets longer, while watts stay tied to volts times amps.
- Voltage drop is the loss along the wire, and it grows with length and current.
- Cord gauge, insulation and plug rating all limit the load, not the length alone.
- Add up the power of every device on the cord before choosing a gauge.
 

## How length and amperage relate 

Extension cord length and amperage are linked through the resistance of the copper wire. A longer cord adds more wire, so more of the supplied voltage is lost as heat before the power reaches the tool. The same gauge that carries a load over a short run may become unsafe over a long one. 

The wire gauge sets the baseline, and the gauge is written as an AWG number such as 16 AWG, 14 AWG or 12 AWG. A lower AWG number means thicker wire with lower resistance. Thicker wire handles more current and loses less voltage along the same distance. 

The circuit feeding the cord also sets a ceiling on the current. A cord plugged into a 15 amp circuit cannot safely pass more than the circuit breaker allows, whatever the cord can carry. The weakest link in the chain decides the real limit. 

## Reading a length and amp chart 

An extension cord length amperage size chart lists wire gauges against run lengths and gives the current each combination can carry. Read down the chart for your gauge and across for your length. The number where they meet is the amperage rating for that run. 

Short lengths accept lighter gauge, and long lengths demand heavier gauge for the same amperage. A short 16 AWG cord suits a small lamp, while a long 12 AWG cord serves a heavy tool. The chart makes that trade visible before you buy. 

Treat chart values as a ceiling, not a target. The actual load depends on the device, the ambient heat and the condition of the cord. Add a margin so the run stays below the rating. 

## Calculating the load on a cord 

An extension cord load calculator works from watts and volts. Find the watts on each device label, add them together, and divide by the supply voltage to get amps. A cord rated for that amperage over your run length is the minimum you need. 

Maximum cable load calculation also accounts for continuous draw. Devices that run for long periods heat the wire more than a brief surge does. A safe continuous load sits below the cord rating, so leave room for a margin. 

Voltage drop over distance changes the picture for long runs. Calculate the drop from current, wire resistance and length, then check that the device still receives enough voltage. Motors and compressors draw more current when voltage sags, which makes the problem worse. 

## Gauge versus amperage by length 

Wire gauge versus amperage is the core decision in cord choice. Each gauge has a current limit for a given length, and the limit falls as the run grows. Choose the gauge that carries your amps over your distance with margin left. 

A 12 AWG cord is the heavier choice for long runs and big loads. A 14 AWG cord covers moderate loads over shorter runs. A 16 AWG cord is for light loads only, and it should stay short. 

Voltage drop by length matters as much as the amp rating. A cord can carry its rated current and still deliver low voltage at the far end if the run is long. Check both figures when the run is long. 
| Gauge | Current bracket | Typical run use | 
| 16 AWG | Light | Short runs for lamps and small chargers | 
| 14 AWG | Moderate | Medium runs for light tools | 
| 12 AWG | Heavy | Long runs for power tools |  

## Watts a cord can handle 

How many watts an extension cord handles comes from its amperage rating times the supply voltage. A cord rated for a given current carries that many amps at your local voltage. Multiply the two to get maximum watts on the extension cord. 

The device label gives the watt figure you need. Add the watts of every device on the run, then compare the total with the cord's watt capacity at your length. If the total is close to the limit, step up to a heavier gauge. 

Power load per device varies with the tool. Heaters and motors draw a steady high current, while electronics draw little. Plan for the largest combined load you might plug in at once. 

## Choosing a length that fits the job 

Maximum extension cord length depends on the gauge and the load, not a single number. Short runs of a given gauge carry more current than long runs of the same wire. Pick the shortest cord that reaches the work, then confirm the gauge handles the amps. 

Typical cord lengths range from a few feet to a hundred feet, and each step adds resistance. A heavy duty extension cord 100 ft should use thick wire such as 12 AWG to carry a serious tool. A thinner cord at that length suits only light loads. 

An average extension cord length for a household does not define a safe run. The safe maximum run length is the length at which your load still receives adequate voltage. Set that from the chart and the load, not from habit. 

## Outdoor runs and heavy loads 

An outdoor extension cord needs insulation rated for weather and a gauge sized for the distance. Outdoor runs are often long, so voltage drop compounds the problem. Heavier gauge and a shorter run keep the outdoor load safe. 

Long runs to a workshop or a yard tool put strain on the cord and the supply. Use a cord rated for the outdoor load and check the plug and jacket for damage before each use. Damaged insulation on a wet run is a shock risk. 

Where a run is permanent or the load is heavy, a fixed installation by a qualified electrician is the correct answer. Extension cords are for temporary use, and a run that needs a fixed supply should not rely on a cord. 

## Mistakes that overload a cord 

A frequent mistake is daisy-chaining cords to gain length without checking the gauge. Each link adds resistance and heat, and the last cord may carry more than it can handle. One cord of the right gauge beats several joined ones. 

Another error is ignoring the plug and socket rating on the cord itself. The wire and the connectors both have limits, and a weak connector overheats before the wire does. Match the whole cord assembly to the load. 

Coiling a cord while it carries current traps heat inside the coil. Unroll the full length before use, especially on a long run with a heavy load. A coiled cord can overheat even well within its amperage rating. 

## Extension cord length and load questions 

### What is the maximum extension cord length I can use? 

Maximum extension cord length depends on gauge and load, not a fixed number. A short run of a given wire carries more current than a long run of the same wire. Pick the length from the chart for your gauge and current, then confirm voltage drop at the far end. 

### How many watts can an extension cord handle? 

The watts an extension cord handles equal its amperage rating times the supply voltage. Find that amperage from the length and amperage chart for your gauge. Compare it with the total watts printed on the device labels before you plug in. 

### What gauge wire do I need for a 100 ft cord? 

A 100 ft cord for a heavy tool needs thick wire such as 12 AWG, because length adds resistance. A lighter 14 AWG or 16 AWG cord at that length suits only lighter loads. Match the gauge to the current your device draws. 

### How do I calculate the load on an extension lead? 

Add the watts of every device on the lead, then divide by the supply voltage to get amps. Check that amperage against the chart for your cord gauge and run length. Leave a margin so the continuous load stays below the rating. 

### Why does a long extension cord reduce power? 

A long extension cord adds resistance along the wire, which drops voltage before it reaches the device. Voltage drop over distance grows with length and current. The device may run weakly or draw more current, so use a heavier gauge for long runs. 

### Can I join two extension cords to make a longer run? 

Joining two extension cords adds resistance and heat at the plugs, and it can exceed the rating of the lighter cord. The safe maximum run length is set for one cord of the right gauge. Use a single cord rated for the load instead of chaining short ones.
