How to Mount or Hang a Dry Erase Board for a Bracket

Plan the wall, set the height and fix a dry erase board so brackets hold it level and secure. Covers anchors, hardware and magnetic boards.

8 min read1 viewsHow to Mount or Hang a Dry Erase Board for a Bracket
— · 0 votes
Contents
  1. Choose the mounting method for the board
  2. Fix the bracket display height
  3. Gather the right hardware for the wall
  4. Mark and drill the bracket holes
  5. Hang the board on the brackets
  6. Stick a magnetic board to a smooth wall
  7. Level, tighten and check the board
  8. Dry erase board bracket questions
  9. What are dry erase board hanging brackets?
  10. How do I hang a dry erase board on drywall?
  11. How do I hang a dry erase board without a helper?
  12. Can I stick a magnetic board to the wall instead of using brackets?
  13. Where should the bracket display height be set?
  14. Which wall anchors suit a board mounting kit?

Mounting a dry erase board for a bracket means fixing wall mounting brackets or a board mounting kit to the wall at a level height. You choose hardware for the wall type, mark the holes, drill and anchor, then hang or fix the board so it cannot shift. A magnetic board follows the same steps when it hangs from a bracket or a cleat.

  • Match the wall anchors to the wall material before you drill any hole.
  • Mark the bracket height from the floor so the writing surface sits level.
  • A board mounting kit often supplies the brackets, screws and anchors together.
  • Magnetic boards need a flat wall and firm fixings because the surface pulls on the wall.
  • Check the board with a level after hanging and tighten every fixing.

Choose the mounting method for the board

A dry erase board reaches the wall by one of a few methods, and the method shapes the bracket you need. Bracket rails, a French cleat and corner clips each spread the load in a different way. Heavy boards need a fixing that sits in studs or in firm anchors rather than in the surface layer of the wall.

A board mounting kit is a packaged set of brackets, screws and anchors sold for this job. Check that the kit states a load rating that covers your board, and check that the bracket length suits the board frame. A rail that is shorter than the board can bend the frame when you tighten the fixings.

Hanging a bracket board on a hollow wall changes the plan, because the plasterboard alone holds almost nothing. Drywall anchors spread the load behind the surface, and studs carry far more weight than any anchor. Plan the bracket positions so at least some fixings land on studs when the spacing allows.

Fix the bracket display height

Bracket display height decides how the board feels when people write on it, so set the height before you drill. A board set too high forces the arm upward and strains the shoulder. A board set low makes the lower edge hard to reach.

Measure from the floor to the top edge of the board, not to the bracket, then subtract the drop of the bracket. Ask a person who will use the board to stand at the wall and mark a comfortable reach line. Place the vertical center of the board near that line.

Keep the board away from door swings, heat sources and direct sun where possible. A magnetic board wall installation also needs a flat spot, because a curved wall lifts the frame from the brackets. Use a level on a long straightedge to find the high and low points of the wall.

Gather the right hardware for the wall

Mounting hardware must match both the board and the wall, and a mismatch causes most mounting failures. Read the bracket holes and measure the screw size they accept. Then choose a screw long enough to reach the anchor or stud behind the surface.

Wall mounting brackets for a light board may work with short screws into studs or with toggle-style anchors in a hollow wall. A heavy framed board needs longer fixings and more of them. Do not reuse old anchors from a previous board, because the hole has already lost its grip.

Assemble the small parts before you climb a ladder, so screws, anchors and spacers sit within reach. A pencil, a tape measure, a level and a drill with the right bit size complete the set. Safety glasses and a helper for lifting protect you during the lift.

Mark and drill the bracket holes

Marking the holes is the step that decides whether the board ends level, so take the time to do it twice. Hold the bracket against the wall at the measured height and mark each hole with a pencil. Check the marks with a level across the bracket before you drill.

Drill each hole to the diameter that the anchor maker states for that anchor type. A hole that is too wide lets the anchor turn without gripping, and a hole that is too narrow splits the wall. Hold the drill straight so the hole does not wander, then clear the dust from it.

Press each wall anchor into its hole and set it as the maker directs. Some anchors expand when you drive the screw, and others need a setting tool first. Slide the bracket over the fixings and tighten the screws in turn so the bracket pulls down evenly.

Hang the board on the brackets

Hanging the board needs a helper when the board is large, because the frame can twist out of your hands. Lift the board so its top edge or its mounting points meet the bracket hooks. Set it down slowly and let the brackets take the weight before you release it.

A rail system lets you slide the board sideways after hanging to fine-tune the position. Corner clips hold the frame at fixed points and leave little room to move. Whichever system you use, check that the board sits fully down in every slot.

Hanging a whiteboard on a cleat means lifting the board until the wall cleat drops into the board cleat. A second person guides the bottom edge away from the wall while the board settles. Do not force the board if it stops, because a misaligned cleat can crack the frame.

Stick a magnetic board to a smooth wall

How to stick magnetic board to wall depends on whether the board is thin and light or rigid and heavy. A thin magnetic sheet can press onto a smooth, clean surface with an adhesive backing. A rigid magnetic board with a frame needs brackets, anchors or a cleat because the weight is greater.

Clean the wall with a cloth and let it dry fully before you apply adhesive, since dust and grease weaken the bond. Press the sheet from one edge and smooth it toward the other edge to push out trapped air. Hold pressure across the whole sheet, then leave the piece undisturbed while the adhesive sets.

A magnetic board wall installation with adhesive suits a wall that will not take screws, but adhesive fixings can fail under heat or heavy use. Where the board must hold notes and magnets long term, use wall mounting brackets and proper anchors instead. Choose the fixing by the weight the board must carry.

Level, tighten and check the board

Level and secure mounting finishes with a check on every fixing and on the board itself. Set a level on the top edge of the board and confirm the bubble sits centered. Loosen the bracket screws a quarter turn only if the level shows a clear tilt.

Tighten each screw until the bracket cannot rock, but stop before the frame or the wall surface compresses. Add a shim behind a low corner if the wall is uneven, rather than forcing the frame. Check that the board cannot slide off the brackets when you push it sideways.

Test the board gently with a light push at the top and the bottom. A board that moves is not secure, so add a fixing rather than ignore the movement. Where the job involves a very heavy board, a high ceiling or a wall of unknown construction, bring in a trained installer.

Dry erase board bracket questions

What are dry erase board hanging brackets?

Dry erase board hanging brackets are the clips, rails or hooks that hold the board on the wall. They attach to the wall with screws and anchors and take the weight of the board. A dry erase board mounting bracket must match the frame depth and the board weight.

How do I hang a dry erase board on drywall?

Hanging a dry erase board on drywall works when you fix into studs or use drywall anchors for the rest of the bracket holes. Mark the bracket height, drill the anchor holes and set the anchors before you tighten the screws. Add more fixings when the board is large or framed.

How do I hang a dry erase board without a helper?

A light board can hang alone if you use a cleat or rail that holds itself in place while you tighten the fixings. Fix the wall half of the cleat first, then lift the board onto it with a slow, straight push. A large or framed board needs a second person for the lift.

Can I stick a magnetic board to the wall instead of using brackets?

A thin magnetic sheet can stick to a smooth, clean wall with its adhesive backing. A rigid magnetic board that carries weight needs wall mounting brackets, screws and wall anchors. Adhesive alone is not a safe choice for a heavy board.

Where should the bracket display height be set?

The bracket display height should place the middle of the board near the comfortable reach line of the person who writes on it. Measure from the floor, subtract the bracket drop and check the mark with a level. Repeat the measurement at the other end of the board.

Which wall anchors suit a board mounting kit?

Use the anchors the board mounting kit or anchor maker specifies for your wall material. A hollow wall takes expanding or toggle anchors, and solid masonry takes a plug made for masonry. A stud carries more weight than any anchor, so place fixings there when the layout allows.

Latest articles