Sport Stacking Competition Timing: Equipment, Attempts, and Results
A practical guide to sport stacking competition timing: choosing stacking timers and timing mats, running valid attempts, recording times, building a bracket, and planning a realistic schedule for a group event.
Contents
What do you need to time a cup stacking competition?
A reliable stacking timer with a timing mat is the core of any sport stacking competition. The timer measures to the thousandth of a second (0.001 s), because stacking times are often separated by a few milliseconds. The mat has touch-sensitive pads: the stacker's hands rest on them at the start and stop the clock when they return to the pads after completing a stack. You will need at least one timer and mat per competition lane. For a casual group event, a single lane works, but two or more lanes let you run head-to-head races and keep the schedule moving.
Other useful equipment:
- 12 identical speed stacks cups per lane (9 for the 3‑3‑3, 12 for the 3‑6‑3 and Cycle)
- A flat, stable table, approximately 76 cm (30 in) high
- A results sheet or spreadsheet to record times
- A visible bracket or schedule so participants know when they compete
How do you start and stop the timer correctly?
Standard start and stop procedures keep results fair. The stacker places both hands flat on the timing mat, fingers in contact with the touch pads. The judge says “Ready, down, go!” On “go” the stacker lifts both hands and begins stacking. The clock starts when both hands leave the pads. After completing the required stacks and downstacking to the original pyramid, the stacker returns both hands to the pads. The clock stops when both hands touch the pads again.
The judge checks that the stacker does not touch the cups before both hands have left the mat and does not stop the timer early. If cups fall during a run, the stacker must fix them. A run is valid only if all cups are stacked and downstacked in the prescribed order and the timer was operated correctly.
What is a valid attempt in cup stacking?
A valid attempt is a completed run in which the stacker follows the rules for the event, no cups remain tipped or out of place, and the timer has started and stopped according to the start and stop procedures. In a competition, each stacker usually gets three attempts at each event (3‑3‑3, 3‑6‑3, Cycle). The best time is used for the result. In a head-to-head race, the first valid run wins the heat; if neither stacker produces a valid run, the heat may be re-run.
How do you record times and handle ties?
Write down every attempt to the nearest 0.001 second. Use a results table with columns for name, event, attempt 1, attempt 2, attempt 3, and best time. For example:
| Stacker | 3‑3‑3 best | 3‑6‑3 best | Cycle best |
|---|---|---|---|
| Alex | 2.145 | 2.892 | 7.305 |
| Jamie | 2.310 | 3.014 | 7.891 |
Ties are rare but possible. In a timed event, if two stackers have identical best times, the tie can be broken by the second-best attempt, then the third. In a head-to-head bracket, if both stackers tie exactly, the heat is re-run once. If the tie persists, you can use a sudden-death single attempt.
How do you build a competition bracket?
A bracket organises head-to-head races and determines a champion. For a small group, a single-elimination bracket works well. If you have a number of participants that is not a power of two (4, 8, 16, 32), use byes in the first round.
Example with 6 stackers:
- Seed the stackers by their best qualifying time (optional, but makes early rounds fair).
- Fill the bracket so the top two seeds get byes and the other four compete in round 1.
- Round 1: Seed 3 vs Seed 6, Seed 4 vs Seed 5.
- Round 2 (semi-finals): Seed 1 vs winner of 4/5, Seed 2 vs winner of 3/6.
- Final: winners of the semi-finals.
Show the bracket on a whiteboard or printed sheet, and update it after each race. Make the next round clear: announce the names of the stackers who advance and point to their place on the bracket.
How do you plan a realistic schedule?
Estimate the time each race takes, then add buffer for timer resets, cup tidying, and announcements. A typical heat for a single stacker’s three attempts takes 1–2 minutes. A head-to-head race takes 3–4 minutes. For a group of 12, running a full 3-event tournament (three rounds of best-of-three attempts each) takes about 3–4 hours. For a casual event, you can run only the Cycle event to reduce time.
Here is a simple schedule for 8 participants, running only the Cycle, with one timer:
| Time | Activity |
|---|---|
| 10:00 | Check-in, lane practice |
| 10:20 | Seeding: one timed attempt per stacker |
| 10:45 | Bracket announcement |
| 11:00 | Round 1: 4 heats |
| 11:30 | Break |
| 11:40 | Semi-finals: 2 heats |
| 12:00 | Final: 1 heat |
| 12:15 | Awards |
Breaks are important: stackers need rest, and the judge can reset the equipment. In a longer competition, schedule a 10-minute break every hour.
What changes when you use multiple timers?
With two or more lanes, you can run heats simultaneously, which cuts the competition time almost in half. For a double-elimination bracket, you need more rounds, so multiple timers are highly recommended. Assign one judge per lane, and use a central results table. Each judge records times and reports the winner. Announce results clearly after each round.
Related articles
Sport Stacking Competition Rules Explained
Learn the essential rules of sport stacking competitions, including individual and relay events, how to set up brackets, schedule rounds, and run a smooth event with friends.
How to Organize a Sport Stacking Competition
A practical guide to organizing a sport stacking competition for beginners: events, divisions, stations, judges, brackets, realistic schedules, progression and clear results.
How to Find Sport Stacking Tournaments Near You and Organize Your Own Event
Find sport stacking tournaments near you through listings and local contacts, or turn a group of friends into an organized event with a fair bracket, a realistic schedule and clear round announcements.